CCTV Power Supply Guide: Sizing 12V PSUs for HiLook Cameras
Topics
- Hikvision Client Software
- Hikvision Firmware
- Hikvision Tools Software
- Alarm
- Hikvision ColorVu Technology
- Hikvision Warranty
- Hikvision Company News
- LiveGuard
- IVMS-4200
- AoC
- Hybrid
- Specifications
- AcuSeek
- Hikvision Video Intercom
- Security
- How To
- Ajax
- Fire Detection
- Ruiji
- AcuSense
- 12MP
- 16MP
- Router
- Hilook IP Cameras
Tags
A camera that works all day and drops out the moment its night lights switch on is rarely a faulty camera. It is nearly always the power. This CCTV power supply guide is for UK installers fitting HiLook Turbo HD systems, and for end users who want to understand what is on the quote. It explains what a 12 V DC camera actually needs, how much current the popular HiLook cameras draw, how to size a supply for 1, 4, 8 or 16 cameras, how to deal with voltage drop on long runs, and which power supplies, splitters and test tools to order. Every specification is cited to the Hikvision datasheet or another named source next to the claim.

What this guide covers
- What the camera needs: a regulated 12 V DC feed that stays inside the tolerance printed on the datasheet.
- How much each HiLook camera draws: maximum wattage from the datasheets, converted to amps.
- How to size the supply: a simple sum with worked examples for 4, 8 and 16 cameras.
- Which supply to fit: plug-in, encapsulated with a splitter, or a 20-way boxed unit.
- Long runs, recorders and Power over Coax: voltage drop, the DVR’s own adapter and when PoC applies.
- Fault-finding and safety: the symptoms of a weak supply and the UK rules worth knowing.
What power supply does a CCTV camera need?
A HiLook Turbo HD camera needs a regulated 12 V DC supply that can deliver more current than the camera’s maximum draw, measured at the camera and not at the power supply. The voltage figure on the label of the supply is only half the story, because cable resistance takes its share before the power reaches the camera.
The datasheets set the limits. The HiLook THC-T120-MS datasheet gives the power requirement as 12 VDC ± 25%, with a maximum consumption of 3.7 W. A tolerance of 25% either side of 12 V works out at a window of 9 V to 15 V at the camera terminals. Stay inside that window with the night lights on and the camera is happy. Drop below it and you get the classic night-time faults covered later in this guide.
Three practical points follow from that:
- Regulated, not just rated. A regulated supply holds its output steady as the load changes. That matters because a camera’s draw rises when its infrared or white light switches on.
- DC, not AC. Fixed HiLook Turbo HD cameras are 12 V DC devices. Some PTZ cameras use 24 V AC, and the two must never be swapped.
- Size on the maximum, not the average. The datasheet maximum is the figure with the lights at full power, which is exactly when a marginal supply fails.
How much power does a HiLook Turbo HD camera draw?
Current HiLook Turbo HD turrets draw between roughly 3 W and 5.5 W at full load, which is about a quarter to just under half an amp at 12 V. The table below lists the datasheet maximum for popular models and converts it to current using amps = watts ÷ volts.
| Model | Type | Datasheet maximum | Current at 12 V |
|---|---|---|---|
| THC-T120-MS(2.8mm) | 2MP IR turret with mic | 3.7 W (datasheet) | about 0.31 A |
| THC-T159-MS(2.8mm) | 3K ColorVu turret with mic | 2.9 W (datasheet) | about 0.24 A |
| THC-T259-MS(2.8mm) | 3K ColorVu turret, longer-range white light | 4.2 W (datasheet) | 0.35 A |
| THC-B159-LTS (reference model) | 3K two-way audio mini bullet | 5.3 W (datasheet) | about 0.44 A |
Two things stand out. First, a stronger light costs power: the THC-T259-MS, with white light rated up to 40 m on its datasheet, draws more than the THC-T159-MS, rated up to 20 m. Second, cameras with a built-in speaker sit at the top of the range. The THC-B159-LTS figure is included as a reference for the two-way audio family; for the models we stock, the THC-T257-LTS(2.8mm) turret and the THC-B157-LTS(2.8mm) mini bullet, read the maximum from the datasheet for the exact model before you size the supply, and allow at least the reference figure in the meantime. The same goes for the 8MP THC-T180-M(2.8mm).
How do you size a CCTV power supply?
Add up the maximum wattage of every camera on the supply, divide by 12 to get amps, then choose a supply with spare capacity above that figure. We suggest at least a quarter spare as a working rule, so the supply runs cool and has something in hand for cable losses and a future camera.
Worked examples using the THC-T259-MS at 4.2 W (datasheet):
| Cameras | Total load | Current at 12 V | With a quarter spare | Supply that fits |
|---|---|---|---|---|
| 1 | 4.2 W | 0.35 A | 5.25 W | 2 A (24 W) plug-in |
| 4 | 16.8 W | 1.4 A | 21 W | 5 A (60 W) with 4-way splitter |
| 8 | 33.6 W | 2.8 A | 42 W | 5 A (60 W) with 8-way splitter |
| 16 | 67.2 W | 5.6 A | 84 W | 20 A (240 W) 20-way boxed supply |
The 16-camera row is the one that catches people out. Sixteen cameras at 5.6 A is already over the rating of a 5 A supply before any margin is added, so a pair of small supplies or a single boxed unit is the right answer. Mixed systems are sized the same way: add each camera’s own maximum rather than assuming they all match.
Which CCTV power supply should you fit for 1, 4, 8 or 16 cameras?
Fit a plug-in supply for a single camera, an encapsulated supply with a splitter for small domestic systems, and a boxed multi-output supply for anything of eight cameras or more that you want to maintain easily. The options we stock line up with those three jobs.
- One camera or a spare feed: the 1-way 12 V DC 2 A (24 W) UK plug-in power supply. Useful for a single added camera, a microphone or a bench test.
- Four cameras: the 4-way 12 V DC 5 A (60 W) encapsulated power supply, supplied with a 4-way splitter. It is the standard choice beside a 4-channel recorder.
- Six or eight cameras on one 5 A supply: swap the lead for a 6-way splitter or an 8-way splitter, provided the sum above still leaves headroom. A spare 4-way splitter is worth carrying for service calls.
- Eight to sixteen cameras and commercial jobs: the 20-way 12 V DC 20 A (240 W) metal boxed power supply, which has twenty 1 A outputs each protected by its own PTC resettable fuse.
For terminating your own power leads, the screw-terminal male 2.1 mm DC connector and female 2.1 mm DC connector save cutting moulded tails, and a ready-made 20 m RG59 coax and power lead carries video and 12 V in one run for a quick domestic fit.

Is a splitter or a boxed power supply better?
A boxed supply with individually fused outputs is the better engineering choice, because a fault on one camera cable is contained to that output instead of taking every camera down. A splitter is cheaper and perfectly sound on a small system that has been sized properly, but it shares one output between all the cameras.
Hikvision’s own position is the most cautious of all: the HiLook THC-T157-LPS datasheet, for example, recommends one power adapter per camera. A boxed supply with a separate protected output for each camera is the practical way to honour the intent of that advice on a multi-camera job without a row of plug-tops.
- Splitter on one supply: lowest cost, neat beside a 4-channel recorder. A short circuit on any leg shuts down the whole supply, so every camera goes dark together.
- Boxed 20-way supply: one output per camera, each limited to 1 A. A damaged cable trips its own fuse and the other cameras keep recording. Screw terminals also make it easy to isolate a single camera during fault-finding.
- Separate plug-in supplies: full independence, but more sockets, more clutter and more points of failure.
How far can you run 12 V to a CCTV camera?
There is no single distance figure, because the limit depends on the cable’s conductor size and the camera’s current; what matters is that the camera still sees at least 9 V under full load. That lower limit comes from the 12 VDC ± 25% tolerance on the THC-T120-MS datasheet.
Voltage drop follows Ohm’s law: the volts lost in the cable equal the current multiplied by the cable resistance, and the resistance rises with length and falls with conductor thickness. So a long run of thin cable feeding a camera with a powerful light is the worst case, and a short run of heavy cable feeding a low-draw camera is the best.
How do you measure voltage drop on site?
Measure at the camera end, with the camera connected and its lights on. The Haydon HAY-DC-M inline DC volt and amp meter plugs in line with the 2.1 mm power lead and shows both the voltage reaching the camera and the current it is drawing, across a 5 V to 35 V DC range. Cover the camera’s light sensor to force night mode, then read the meter. A healthy reading in daylight proves nothing about the night-time load.
What do you do if the voltage is too low?
- Shorten the power run: move the supply closer to the camera, or fit a local supply at the far end of the building.
- Use heavier conductors: a thicker power core loses less. Thin pairs in data cable are the usual culprit.
- Double up cores: where power travels over Cat5e or Cat6 with baluns, pair spare cores together for the positive and negative legs.
- Do not turn the voltage up to compensate: a supply set high to rescue a long run can exceed the upper limit of a camera on a short run fed from the same unit.
If the job is wired in twisted pair, the Netview NV-HY102C-HD 4K push-fit balun and the 4-camera and 8-camera connector kits handle the video, but the power still travels down thin copper, so measure every long leg.
Does the DVR need its own power supply?
Yes: the recorder runs from its own adapter, and that adapter should not be shared with the cameras. As a guide to scale, the HiLook DVR-204Q-M1/T datasheet specifies a 12 VDC, 1.5 A supply and a consumption of no more than 8 W without a hard drive. The hard drive adds its own load on top, most of all at spin-up.
Tapping camera power from the recorder’s adapter leaves the recorder short exactly when the drive and the camera lights both demand current. Keep them separate. The same applies across the range we stock, from the DVR-204G-M1/T and DVR-208G-M1/T to the DVR-208U-M1/T and the 16-channel DVR-216Q-M1/T: check the power line on the datasheet for the exact model and use the adapter supplied with it.
Where the customer cares about footage surviving a power cut, put the recorder, the camera supply and the router on the same protected feed. A recorder that stays up while the cameras lose power records nothing useful.
Can you power HiLook cameras over the coax with PoC?
Only if both the camera and the recorder are Power over Coax models; a standard 12 V DC HiLook camera cannot take power from the coax. Hikvision’s PoC technical bulletin describes PoC as carrying the high-definition video, the coaxial control signal and the power on one coaxial cable, with two camera classes: AF at 6 W and AT at up to 12 W.
The same bulletin notes that the PoC module supplies 48 VDC, that the recorders support only Hikvision PoC cameras, and that ordinary non-PoC cameras should be powered up before they are connected. In other words, PoC is a matched system, not a way to rescue a job that is short of power cable. The cameras in the table above list a 12 V DC input on their datasheets, so they need a conventional supply.
Where a PoC system is specified, we stock the Netview NV-HY801C-HD 4K PoC balun for twisted-pair runs and a 52 V DC 2.3 A (120 W) power supply listed for PoE and PoC equipment. Our explainer on Hikvision PoC covers the technology in more detail.

What are the signs of a failing or undersized CCTV power supply?
The tell-tale sign is a fault that follows the lights: the picture is fine by day and fails, flickers or reboots at dusk, when the camera’s draw peaks. Because the load is highest at night, a weak supply or a long cable shows itself then and not during a daytime handover.
- Picture drops out at night and returns in the morning. The voltage at the camera is falling below its limit when the lights come on.
- Camera restarts in a loop after dark. The lights switch on, the voltage sags, the camera resets and the cycle repeats.
- Several cameras fail together. A shared supply is overloaded or has shut down on a fault on one leg.
- Faults appear after adding a camera. The extra load has used up the headroom.
- The supply runs hot or hums. It is working at or beyond its rating and is due for replacement.
Work through it in order: measure at the camera under night load, then at the supply, then swap the supply for a known good one. If power checks out, our HiLook DVR no video troubleshooting guide covers signal format, cable and connector faults, and the HiLook Turbo HD system guide covers matching cameras to recorders.
What safety rules apply to CCTV power supplies in the UK?
The 12 V side is extra-low voltage, but the supply itself is mains equipment, so it must be a compliant product and any work on the mains side must be done by a competent person with the circuit isolated. Two official sources are worth knowing.
- Product compliance: GOV.UK guidance on the Electrical Equipment (Safety) Regulations 2016 explains that the rules cover equipment designed for 50 to 1,000 V AC, which includes mains-powered supplies, and that such equipment must meet the essential safety requirements and carry UKCA or CE marking.
- Working practice: the Health and Safety Executive’s guidance on work on electrical equipment says work should be planned, energy sources isolated so they cannot be restored by accident, and the work carried out by people who can show they are competent.
On site that means: fit boxed supplies indoors in a dry, ventilated location; do not bury a supply in loft insulation; never substitute a 24 V AC unit such as the 24 V AC 2 A inline supply for PTZ cameras for a 12 V DC one; and label each output so the next engineer can isolate a single camera.
Frequently asked questions
Can I run four cameras from one CCTV power supply?
Yes. Four THC-T259-MS turrets total 16.8 W, or 1.4 A, based on the 4.2 W maximum on the datasheet, which a 5 A supply with a 4-way splitter handles with plenty in hand.
Is a 1 A power supply enough for one camera?
For the models in this guide, yes on paper, since the highest figure listed is 5.3 W, about 0.44 A. In practice a 2 A plug-in supply costs little more and leaves room for cable losses.
What happens if the voltage at the camera is too low?
The camera may restart, lose picture or misbehave when its lights switch on. The limit on the THC-T120-MS datasheet is 12 VDC ± 25%, so aim to stay comfortably above 9 V under full load.
Can I use the DVR power adapter to run a camera as well?
No. The recorder’s adapter is sized for the recorder and its hard drive. Give the cameras their own supply.
Do HiLook IP cameras need a 12 V power supply?
Not normally. HiLook IP cameras are usually powered over the network cable from a PoE recorder or switch, so a separate 12 V supply is only needed where PoE is not available. This guide concerns Turbo HD analogue cameras on coax.
Should I choose a higher-amp supply than I need?
Yes, within reason. A camera only draws the current it needs, so a larger 12 V supply does no harm and runs cooler. What you must not exceed is the voltage.
Order CCTV power supplies and HiLook cameras from Netview
Netview is a Leicester-based authorised HiLook and Hikvision wholesaler with same-day dispatch on stocked lines. Browse the 12 V DC power supplies, splitters, connectors, test meters, HiLook Turbo HD cameras and DVRs in this guide, check live trade stock and order online at netviewcctv.co.uk.
Share this post


About the Author

Netview CCTV Ltd is an Authorised Hikvision Wholesaler: Verify
- Website:https://www.netviewcctv.co.uk
- E-mail:[email protected]
- Our Hikvision Authorised Partner ID:HIK00004832
Our business has established itself as a highly trusted Trade distributor & retailer specializing in Leading Edge CCTV surveillance systems & accessories.
We have the technical expertise to help you make the correct choice for your requirements.
All the products we sell offer excellent value for money, outstanding quality and superb performance
We are a Bricks & Mortar company, not just online, and we hold substantial stocks ready for immediate dispatch or collection at our premises in Leicester.
We are authorized Hikvision UK Distributors and offer full UK Hikvision Warranty with all our products. All products are fully upgrade-able with UK firmware.
Our contact details are:
Netview CCTV Ltd
Earls Way
Leicester
LE4 8FY UK
Telephone Leicester: 0116 3800838
Email Sales: [email protected]
Support: [email protected]
Website: www.netviewcctv.co.uk
Our page on FACEBOOK
Follow us on Twitter: @netviewcctv
Watch our videos & demos on YOUTUBE
Netview CCTV Ltd follows the ICO's guidance on video surveillance (including CCTV) under UK GDPR and the Data Protection Act 2018. This can be found at ico.org.uk
Netview CCTV, netviewcctv, netviewcctv.co.uk, netviewcctv.com are all trading names for NETVIEW CCTV Ltd registered in the UK company reg number: 08412263



