Dual WAN Failover for CCTV: The Reyee Internet Backup Guide
Topics
- Hikvision Client Software
- Hikvision Firmware
- Hikvision Tools Software
- Alarm
- Hikvision ColorVu Technology
- Hikvision Warranty
- Hikvision Company News
- LiveGuard
- IVMS-4200
- AoC
- Hybrid
- Specifications
- AcuSeek
- Hikvision Video Intercom
- Security
- How To
- Ajax
- Fire Detection
- Ruiji
- AcuSense
- 12MP
- 16MP
- Router
- Hilook IP Cameras
Tags
When a customer’s broadband drops, the cameras keep recording but nobody can see them, the alarm panel loses its main signalling path and the first call is to the installer. This guide is for UK CCTV and security installers who want to fit dual WAN failover on a Ruijie Reyee gateway, so that a second internet line takes over automatically when the first one fails. It covers how failover differs from load balancing, which Reyee EG routers support it, how to use a 4G router as the backup line, the link detection settings that decide when the switch happens, and how to test it before handover. Figures come from Ruijie’s own pages and datasheets and are cited next to each claim.

What this guide covers
- Failover or load balancing: the two multi-WAN modes on Reyee EG routers and which one a CCTV site needs.
- Which router: EG models with 2, 4 and 9 WAN ports, from a small shop to a multi-building site.
- 4G backup: using the RG-EW300T as the second line, and why mobile data changes how remote viewing must be set up.
- Link detection: the four settings that decide how quickly the router switches over and back.
- Testing and handover: a pull-the-cable test, power backup, and what to write on the job sheet.
What is dual WAN failover, and why does a CCTV site need it?
Dual WAN failover means a router has two separate internet connections and moves all traffic to the second one automatically when the first stops working. A CCTV site needs it because remote viewing, push alerts, cloud backup and alarm signalling all stop the moment the only internet line fails, even though the recorder itself carries on.
The need has grown as phone lines move to broadband. The UK government’s guidance on the landline switchover says most customers are expected to have made the switch by the end of January 2027, and that digital landlines and routers will not function in a power cut unless there is a backup power system such as a battery or generator. The same page advises people with telecare devices to check whether the device needs its own battery and network backup, or can be connected to mobile services such as 4G. In plain terms, the router is now the single point of failure for the phone, the alarm and the cameras. A second line and a small battery backup remove that weakness.
For an installer this is also a straightforward upsell. A shop, a farm, a care setting or a remote-monitored yard that pays for monitoring should not lose it because of one fault at the street cabinet.
What is the difference between failover and load balancing?
Failover keeps the second line idle until the first one fails, while load balancing uses both lines at the same time and shares traffic between them. For most CCTV sites with a broadband line and a metered 4G backup, failover is the right choice because it keeps mobile data use to a minimum.
Ruijie describes both modes in its article on Reyee router traffic balancing. In the mode it calls Failover Mode (Active-Secondary), one WAN is the primary, the others are backups, and the backup interfaces activate only when the primary interface fails. In Load Balancing Mode, each WAN port is given a weight and traffic is shared out according to it. The two can be combined: Ruijie’s own example uses three lines, with two sharing the load and a third that activates only if both of the others fail.
| Mode | How the lines are used | Best for | Watch out for |
|---|---|---|---|
| Failover (Active/Secondary) | Primary carries everything; backup wakes only on failure | Broadband plus 4G backup | Backup line is never exercised unless you test it |
| Load balancing | Both lines active, shared by weight | Two unmetered fixed lines | Uses data on both lines all the time |
| Both combined | Two lines share the load, a third stands by | Larger sites with three lines | Needs a router with three or more WAN ports |
Which Reyee EG router supports dual WAN failover?
The Reyee EG families that Ruijie lists for multi-WAN have between two and nine WAN ports, so the choice comes down to how many lines, how many users and whether you want PoE ports on the router. A small site suits the EG100 series, a busier one the EG200 or EG300 series, and a large site the RG-EG1510XS.
Ruijie’s traffic balancing article lists the WAN port count for each family: 2 on the EG100 series, 4 on the EG105GW-X, the EG200 series, the EG210G-E and the EG300 series, and 9 on the EG1510XS. The entry model, the RG-EG105G-V3, is listed by Ruijie with dual WAN, load balancing and link weight, along with IPSec, OpenVPN, PPTP and L2TP VPN. Its PoE sibling, the RG-EG105G-P-V3, adds four PoE+ ports on a 54 W budget and is recommended for 100 concurrent clients, which lets it power a handful of cameras or an access point without a separate switch.
Where the customer also needs Wi-Fi from the same box, the RG-EG105GW-X has a built-in Wi-Fi 6 access point and four WAN-capable ports. For busier sites, the RG-EG210G-E and its PoE version, the RG-EG210G-P-V3, give four WAN ports in a ten-port chassis.
The RG-EG310GH-E is the model to quote when the specification has to be shown in writing. Its official datasheet lists 10 RJ45 ports, of which 1 is a fixed WAN port and 3 are switchable LAN/WAN ports, giving a maximum of 4 WAN ports. It lists WAN failover and an Active/Standby mode that automatically switches to the standby interface when the active interface fails, a recommended 350 concurrent clients and 1500 Mbps throughput. The RG-EG310GH-P-E and the five-port RG-EG305GH-P-E are the PoE members of the same family. At the top, the RG-EG1510XS supports up to nine WAN ports for sites with several lines or several buildings.
| Site | Suggested gateway | WAN ports (Ruijie) | Why |
|---|---|---|---|
| Home or small shop, 4 to 8 cameras | RG-EG105G-V3 or RG-EG105G-P-V3 | 2 | One broadband line plus one 4G backup |
| Office or cafe needing Wi-Fi from the router | RG-EG105GW-X | 4 | Built-in Wi-Fi 6, spare WAN ports |
| Pub, school block or warehouse | RG-EG210G-E or RG-EG310GH-E | 4 | Two fixed lines plus 4G standby |
| Multi-building or multi-tenant site | RG-EG1510XS | 9 | Several lines, fibre uplinks |
What should you use as the backup internet line?
Use a line that fails for different reasons from the main one, which in practice means 4G mobile data for most small sites and a second fixed line from a different network for larger ones. Two broadband services that share the same street cabinet or the same duct will usually fail together.
The simplest backup is a 4G router plugged into the gateway’s second WAN port. The RG-EW300T is Reyee’s 4G LTE router, described by Ruijie as offering up to 150 Mbps download speed with four external antennas. Ruijie’s page does not list an automatic wired-to-4G switchover on the RG-EW300T itself, so treat it as the mobile line and let the EG gateway make the decision: connect a LAN port on the RG-EW300T to the second WAN port on the gateway and set that port as the secondary.
Before fitting it, check mobile signal at the cabinet with a phone on the same network as the SIM, and put the 4G router where the signal is best rather than where it is tidiest. A backup line with one bar of signal is not a backup.
How do you set up failover on a Reyee EG gateway?
Connect both lines, set the load mode to Active/Secondary, give each WAN port its priority and switch on link detection. Ruijie’s guidance is to set the load mode to Active/Secondary and assign the primary and secondary priorities to the corresponding WAN ports.
- Connect the lines. Main broadband into the fixed WAN port, the backup line into a second WAN or LAN/WAN port.
- Enable the second WAN. In the gateway’s web interface or the Ruijie Reyee app, enable the second WAN port and configure each line (DHCP, PPPoE or static) as the provider requires.
- Choose the mode. Select Active/Secondary and mark the broadband line as primary and the 4G line as secondary.
- Turn on link detection. Without it the router only notices a dead cable, not a dead internet service.
- Decide on forced switch-back. Choose whether traffic should return to the primary as soon as it recovers.
- Save, then test. Do not leave site until you have watched the switchover happen.
Menu names vary slightly between ReyeeOS versions, so follow the labels on the unit in front of you rather than a screenshot from an older release. For a fuller walk-through of the EG range itself, see our Reyee EG series gateway and router guide.

Which link detection settings matter?
Four settings control failover timing: the detection interval, the number of failed rounds before a line is marked offline, the number of good rounds before it is marked online again, and the address the router tests against. Together they decide how fast the switch happens and how often it happens by mistake.
Ruijie’s article names them as Detection Interval, Rounds for Going Online, Rounds for Going Offline and Detected Destination IP, and says the detection target can be a destination IP address or a domain name. It does not publish default values, so read them off the unit and adjust with these principles in mind.
- Shorter interval, faster switch. The time to fail over is roughly the interval multiplied by the offline rounds. Halving either one halves the wait.
- Too sensitive causes flapping. A line that drops a few packets on a wet afternoon should not trigger a switch to 4G. Keep at least a few offline rounds.
- Pick a dependable test address. Use a well-known public address that is always up, not the provider’s own gateway, which can answer even when the wider internet is unreachable.
- Be slower coming back. More online rounds stop the router bouncing between lines while the main service recovers.
Ruijie also describes a Forced Switch option: with it enabled, traffic on the backup line is cut off immediately when the primary link is restored. On a metered 4G backup that is usually what you want, because it stops live video streams lingering on mobile data.
Will Hik-Connect and remote viewing still work on the backup line?
Yes, provided remote viewing is set up through Hik-Connect or a VPN rather than through port forwarding. Port forwarding depends on the public address of one specific line, so it breaks as soon as traffic moves to a different one.
Many mobile data services place customers behind a shared address, which means inbound connections from the internet cannot reach the site at all. Hik-Connect avoids the problem because the recorder makes the outbound connection to the cloud service, whichever line happens to be active. Set the recorder up that way from day one, as described in our Hik-Connect installer setup and handover guide, and avoid the older approach covered in our port forwarding guide on any site with a mobile backup.
The same applies to the recorder itself. A PoE NVR such as the Hikvision DS-7604NXI-K1/4P(E) or DS-7608NXI-K1/8P(E) needs no change when the line switches: it sits on the LAN, records locally throughout and reconnects to the cloud service once the backup line is up. Expect a short gap in live view while the router detects the failure and the app reconnects. If the site is managed remotely, keep it in Ruijie Cloud as well, as covered in our Reyee Cloud multi-site guide, so you can see which line is active without a visit.
How much mobile data will a CCTV site use on 4G backup?
Very little while nobody is watching, and a great deal if someone leaves live view open. Recording happens on the local hard drive and uses no internet data; only remote viewing, alerts and cloud services use the line.
The arithmetic is simple. A stream of 4 megabits per second is half a megabyte per second, which is 1,800 megabytes, or 1.8 GB, for every hour it is watched. Four cameras at that rate on a video wall would use 7.2 GB an hour. This is why failover mode, sub-stream viewing in the app and forced switch-back matter on a metered SIM.
- Choose a data SIM with an allowance that matches the worst case, not the average month.
- Tell the customer that the system is on backup when it is, so they keep live viewing short.
- Where cameras are on their own network segment, as in our CCTV VLAN setup guide, make sure guest Wi-Fi does not ride on the 4G line during an outage.

How do you test failover before handover?
Pull the main line and watch what happens, then put it back and watch again. A failover that has never been tested on site should be treated as not working.
- Open live view in Hik-Connect on a phone that is on mobile data, not the site Wi-Fi.
- Unplug the primary WAN cable and time how long it takes for live view to return.
- Check the gateway status page or the app shows the secondary line as active.
- Repeat with the cable plugged in but the provider’s modem switched off, which proves link detection works and not just cable detection.
- Restore the primary and confirm traffic moves back.
- Write the two timings on the job sheet with the SIM number and renewal date.
Repeat the test at each service visit. A SIM that has expired or run out of data fails silently, and the first anyone knows is the day the broadband goes down.
What else keeps a CCTV site online during an outage?
Power does. A second internet line is no use if the gateway, the 4G router and the recorder all switch off in a power cut, so the same job should include battery backup for the comms cabinet.
The government guidance quoted earlier makes the point directly: routers powered from the home supply will not function in a power cut without a backup such as a battery. Put the gateway, the 4G router, the provider’s modem and the NVR on a UPS sized for the full load, and remember that PoE cameras draw their power through the switch or NVR, so that load counts too. For sites with no fixed line at all, a camera with its own SIM and solar panel is a different design, covered in our Hikvision solar 4G camera guide.
Frequently asked questions
Do I need a static IP address for dual WAN failover?
No. Failover works with dynamic addresses on both lines. A static address only matters for inbound services such as port forwarding, which should be avoided on sites with a mobile backup.
Can I use two SIMs instead of broadband and 4G?
Yes, with two 4G routers on different mobile networks, each plugged into a WAN port on the gateway. Use different networks, otherwise one mast fault takes out both.
How long does the switchover take?
It depends on the detection interval and the number of offline rounds set on the gateway. Ruijie does not publish default values in its article, so time it on site during the test and record the result.
Does failover work with an Ajax alarm on the same network?
The hub’s Ethernet connection follows whichever line the gateway is using, so it benefits from failover without any change on the hub. Hubs with their own SIM also keep an independent mobile path.
Should I use load balancing instead?
Only when both lines are unmetered fixed lines. With a 4G backup, load balancing would use mobile data all the time.
Will recording stop when the internet fails?
No. The NVR records to its own hard drive whether or not the internet is up. Only remote viewing, alerts and cloud features are affected.
Related guides
- Reyee Networking for CCTV: The Complete UK Buyer’s Guide 2026
- Reyee EG Series Gateways & Routers for CCTV: Installer Buyer’s Guide
- Remote CCTV Monitoring: The Complete UK Installer’s Guide 2026
- Hik-Connect Installer Setup & Customer Handover Guide
Order Reyee dual WAN gateways and 4G routers from Netview
Netview is an authorised UK Ruijie Reyee wholesaler based in Leicester. EG series gateways, the RG-EW300T 4G router, PoE switches and Hikvision NVRs are held in stock for same-day dispatch, with trade pricing for installers. Browse the full Reyee networking range, or see every brand we stock at netviewcctv.co.uk.
Share this post


About the Author

Netview CCTV Ltd is an Authorised Hikvision Wholesaler: Verify
- Website:https://www.netviewcctv.co.uk
- E-mail:[email protected]
- Our Hikvision Authorised Partner ID:HIK00004832
Our business has established itself as a highly trusted Trade distributor & retailer specializing in Leading Edge CCTV surveillance systems & accessories.
We have the technical expertise to help you make the correct choice for your requirements.
All the products we sell offer excellent value for money, outstanding quality and superb performance
We are a Bricks & Mortar company, not just online, and we hold substantial stocks ready for immediate dispatch or collection at our premises in Leicester.
We are authorized Hikvision UK Distributors and offer full UK Hikvision Warranty with all our products. All products are fully upgrade-able with UK firmware.
Our contact details are:
Netview CCTV Ltd
Earls Way
Leicester
LE4 8FY UK
Telephone Leicester: 0116 3800838
Email Sales: [email protected]
Support: [email protected]
Website: www.netviewcctv.co.uk
Our page on FACEBOOK
Follow us on Twitter: @netviewcctv
Watch our videos & demos on YOUTUBE
Netview CCTV Ltd follows the ICO's guidance on video surveillance (including CCTV) under UK GDPR and the Data Protection Act 2018. This can be found at ico.org.uk
Netview CCTV, netviewcctv, netviewcctv.co.uk, netviewcctv.com are all trading names for NETVIEW CCTV Ltd registered in the UK company reg number: 08412263



